Top drivers similar to D-Link Wireless Router. Top drivers similar to D-Link Wireless router Download d link dir 300 installation

D-Link DIR-300 is a router with a Wi-Fi module and four Ethernet ports. Quite a good thing, but there is one drawback: when sold, it contains old firmware, I don’t remember what year it was made. And until you update it, this router periodically becomes quite glitchy.

The new firmware and Russification file can be found here: ftp.dlink.ru. However, before flashing the most new firmware, you need to download the firmware that updates the router to a level compatible with it, namely, download the firmware /upgrade_first/DIR300A1_FW105B07.bin.

This is done as follows:

Go to the MAINTENANCE tab, then select Save and Restore from the menu on the left. In the Save and Restore Settings form, select the Save item and save the router settings to any reasonable location on your hard drive.
Download the firmware from the /upgrade_first directory using the link above.
Go to the MAINTENANCE tab, then select Firmware Update from the menu on the left. At the bottom of the page is the "FIRMWARE UPGRADE" form. Click the "Browse" button and indicate the file DIR300A1_FW105B07.bin that you just downloaded.
Click the "Upload" button and wait for the update process to complete, under no circumstances turning off or rebooting router. Please note that the router Maybe after that, reset the settings to factory defaults and change the IP address to 192.168.0.1.
After rebooting the router, we repeat the two previous steps for the firmware file we took from the directory ftp.dlink.ru/pub/Router/DIR-300/Firmware/. There will be 2 files with the extension .bin, we are interested in the one without “langpack” in the name.
After performing the second update (after which also available factory reset), the LANGUAGE PACK UPGRADE form appears on the MAINTENANCE/Firmware Update page. Using it (similar to using the FIRMWARE UPGRADE form) Can download the Russification file, the same second file with “langpack” in the name. The process is completely similar to updating the firmware.
If during the update a reset to factory settings occurred, on the MAINTENANCE/Save and Restore page in the Save and Restore Settings form, click in the Load Settings From Local line Hard Drive button "Browse" ("Browse") and indicate the settings file that was saved at the very beginning. After that, click the “Upload” button to upload the settings to the router and wait for this process to complete.

Having completed all of the above operations, we will most likely save the router (in my experience) from freezes, sudden resets, inability to see the external network and sometimes the inability to boot with the external network connected. Well, from other bugs, I hope, too :)

Two years have passed since the instructions were written. During this time, D-Link has released several versions of this router. The software for them, in particular firmware, is not in the above directory, but in others:

DIR-300 is the same router about which this post was originally written. In addition, judging by the names of the files, this firmware suitable for DIR-300A1 routers. However, perhaps the first version was simply renamed from DIR-300 to DIR-300A1. Instructions are available DIR-300+A1_Manual+v1.0.pdf.pdf (twice.pdf - if there is a typo, it’s not mine - that’s what the file is called on the server), DIR-300_QIG_RUS_02.pdf, Manual_DIR-300_A1_rev_1_0_RUS.pdf.
DIR-300_C1 - there should be a firmware update here, but on this moment (05.09.2012) she is not there. Only instruction DIR-300_C1_QIG_v6.00(RU).pdf is available.
DIR-300_NRU - please note that for now exists TWO INCOMPATIBLE variant of this router, namely the B1-B2-B3 series firmware and the B5-B6 series firmware. You can distinguish them by reading the sticker on the bottom of the router (see file !!!reamde_first!!!.doc). The firmware is located in the corresponding directories: /B1_B2_B3/ and /B5_B6/. If you flash the wrong firmware, you will most likely have to take the router to a service center.
- /B1_B2_B3/DIR-300NRU_QIG_v.1.2.25_RU.pdf

If you need DIR-300 firmware, then here you will find all the necessary information. A few points worth noting:

If your power goes out during flashing, there is a chance of breaking the router. So first, make sure you have stable electricity and good power cables. You can connect D-link DIR 300 via a UPS for the duration of the firmware.
Updating the firmware yourself will void the warranty.

Why might an update be required? Sometimes you don’t even need an update, but a reinstallation of an existing firmware version. Causes:

The Internet is slow and glitchy.
New functions introduced in the new software version are required.

Firmware is like a driver or operating system for a router. The firmware written to permanent memory devices. First you need to download it.

Brief instructions

In short, the essence of how to reflash:

Download firmware for D-link DIR 300 from ftp.dlink.ru.
Go to the router page 192.168.1.1 (or 192.168.0.1).
Head to the “Maintenance” section, then “Firmware Update”.
Select the firmware file, click “Upload”.
Wait 2 minutes while the router installs the firmware. All.

Now everything is the same, but in more detail.

Firmware download

It weighs only a few megabytes. In the address bar, write the address dlink.ru, then go to the official website of the router developer, this is ftp with firmware.
In the folder called pub, find the Router section.

After that, find the folder with the firmware for your router model and revision, in our example it is DIR-300_NRU.

Next, head to the Firmware folder.

Now you need to find out the revision of the DIR router. You need to take your router, turn it over, and look at what is written on the sticker on the underside.
In this case it is B1, you could have A1/B1/C1/D1/B3/B5/B7/B6.

By opening the folder on ftp called Firmware, select the section that corresponds to your DIR300 router model.

Download the firmware. This is a small file with a bin extension.

Connecting the router to a PC

Connect D-link to your computer via patch cord. You can reflash from regular desktop PCs, laptops and netbooks. Turn on the router. You need to check your network settings.

In Win7, go to “Start”, then to “Control Panel”, then “View network status and tasks”.
Find the “Change adapter settings” link in the left menu. Find the icon for local connection. network, go to connection properties.
A window will open, select protocol version 4 (TCP/IPv4) and click the “Properties” button.

On the “General” tab, see if the settings are set: “Obtain an IP address automatically”, as well as “Obtain a DNS server address automatically”.

Now directly to the firmware update.

Flashing

Open your browser, instead of the site address write 192.168.1.1, you will go to the page generated by the router.
Enter your login and password to access the DIR 300 settings. If you did not set a password, then simply write admin.
On the router page you can find out the revision version (marked with a light green arrow at the top), this is necessary in case the sticker on the bottom of the router has become worn or peeled off.
Go to the “Maintenance” section, then to “Firmware Update. Then go down to “Firmware upgrade”, then “Select file”.
Find the downloaded one on your computer official firmware from D-link. After that, click “Upload”.

The router firmware update will begin, it will take exactly 2 minutes. Do not disconnect the router from power during this time, otherwise it may cause damage.

When the update is finished, you will be redirected to the login and password window.
Look at the top line, if you updated the firmware to a new version, then there should be changes there. If you just reflashed (similar to how reinstalling Windows), then the same firmware version number will be waiting for you.

When the DIR-300 router firmware is reinstalled, the Internet settings do not change. You can continue using your computer immediately.

Firmware for the D-Link DIR-300 C1 model

To reflash D-Link router DIR-300 C1 needs to download the firmware file (.bin) from here.

After that, download the zip archive from here.

Make sure your router is connected to your computer (laptop or netbook) via a cable connection and not via Wi-Fi.
Unpack the downloaded zip archive on your computer and run the dcc.exe program.
After this, D-Link Click’n’Connect will launch. In it, select “Connect and configure a device.”

Update software, it's simple - the tips will help. As a result, not the latest, but working firmware for this model will be installed. If you are satisfied with the operation of the router, then you don’t have to continue.

Updating D-Link DIR-300 C1 to the latest version

But if you want to update the D-Link DIR-300 C1 software to latest version firmware, then...

Go to the router settings, find the “System” section, and then “Software Update”.
There, select the firmware bin file (we downloaded it earlier).
Then click “Update” - wait the standard 2 minutes for an update.

Error messages or the router may freeze, then do not turn off the power, but wait another 5-10 minutes for the installation to complete correctly.

DIR 300 N150 revision D1

Flashing DIR 300 N150 D1 using the example of firmware version 2.5.4 with the new “Air” web interface.

Go to settings in the usual way, you will see the “Start / Information” page, where you can find the exact model name and firmware version.

To install new or reinstall old firmware, click on its version, the “System / Software Update” page will open.
Use the Browse button to select the update file (previously downloaded from here).
Click Update. Waiting 2 minutes.

This is what the firmware file looks like ftp server manufacturer

Restoring settings

If you flashed the DIR-300 unsuccessfully, you can restore the router to factory settings.

The easiest way is to use the RESET button on the router case; you will need a toothpick, since the button is recessed into the case. Press it for 10 seconds, release, after which the router will reboot and start with the settings reset.
You can also use the corresponding item in the web interface settings menu.

You learned how to install the official firmware on the DIR 300 router (revisions A1/B1/C1/D1/B3/B5/B7/B6). Also on our website you can read how to set up the Internet on the D-link DIR 300 router.

Despite the fact that the firmware of the relatively recently widespread Wi-Fi router D-Link DIR-300 D1 is not much different from previous revisions of the device; users have questions related to a small nuance when they need to download the firmware from the official D-Link website, as well as the updated web interface in firmware versions 2.5.4 and 2.5.11.

This instruction will show in detail how to download the firmware and how to flash the DIR-300 D1 new version Software for two versions initially installed on the router - 1.0.4 (1.0.11) and 2.5.n. I will also try to take into account everything in this guide possible problems that may arise.

If you have already connected the router and know how to log into its web interface, you do not need this section. I’ll just note that it’s better to update the firmware via a wired connection to the router.

For those who do not have a router connected yet, and who have never done such things before:

Connect the router with a cable (included) to the computer from which the firmware will be updated. Port network card computer - LAN port 1 on the router. If you do not have a network port on your laptop, then skip this step; we will connect to it via Wi-Fi.
Plug the router into a power outlet. If a wireless connection is used for the firmware, after a while the DIR-300 network should appear, not protected by a password (provided that you have not changed its name and parameters previously), connect to it.
Launch any browser and enter address bar 192.168.0.1. If suddenly this page does not open, check that in the parameters of the connection you are using, in the properties of the TCP/IP protocol, Obtain IP and DNS automatically is set.
When prompted for a login and password, enter admin. (When you first log in, you may also be asked to immediately change standard password, if you change it, don’t forget it, this is the password to enter the router settings). If the password does not work, then perhaps you or someone else changed it earlier. In this case, you can reset the router by pressing and holding the Reset button on the back of the device.

If everything described was successful, we proceed directly to the firmware.

The process of flashing the DIR-300 D1 router

Depending on what firmware version is currently installed on the router, after logging in you will see one of the configuration interface options shown in the picture.

In the first case, for firmware versions 1.0.4 and 1.0.11, do the following:

Click “Advanced settings” at the bottom (if necessary, turn on the Russian interface language at the top, Language item).
Under System, click the double right arrow and then Software Update.
Specify the firmware file that we downloaded earlier.
Click the "Update" button.

After this, wait for the firmware of your D-Link DIR-300 D1 to complete. If you feel like things are frozen or the page has become unresponsive, please go to the Notes section below.

In the second option, for firmware 2.5.4, 2.5.11 and subsequent 2.n.n, after entering the settings:

In the menu on the left, select System - Software Update (if necessary, enable the Russian language of the web interface).
In the "Local Update" section, click the "Browse" button and specify the firmware file on your computer.
Click the "Update" button.

Within a short time, the firmware will be downloaded to the router and updated.

Notes

If, when updating the firmware, it seemed to you that your router was frozen, because the progress bar in the browser moves endlessly or simply shows that the page is unavailable (or something similar), this is simply because when updating the software, the connection between the computer and the router is interrupted, you just need to wait a minute and a half, reconnect to the device (if a wired connection was used, it will restore itself), and go into the settings again, where you can see that the firmware has been updated.

Further setup of the DIR-300 D1 router is no different from setting up the same devices with previous interface options; the differences in design should not scare you. You can look at the instructions on my website, the list is available on the page (I will prepare manuals specifically for this model in the near future).

Install optional products - DriverDoc (Solvusoft) | | | |

This page contains information about installing the latest driver downloads D-Link Wireless router using the D-Link driver update tool.

D-Link Wireless Router drivers are tiny programs that enable your Wireless Router hardware to communicate with your software. operating system. Keeping your D-Link Wireless Router software updated prevents crashes and maximizes hardware and system performance. Using outdated or corrupt D-Link Wireless Router drivers may cause system errors, failures and failure of equipment or computer. Moreover, installing the wrong D-Link drivers can make these problems worse.

Advice: If you are not sure how to update D-Link device drivers manually, we highly recommend downloading the D-Link Wireless Router Driver Utility. This tool will download and update the correct D-Link Wireless Router driver versions automatically, protecting you from installing the wrong Wireless Router drivers.

About the author: Jay Geater is President and general director Solvusoft Corporation is a global software company focused on innovative service programs. He has a lifelong passion for computers and loves everything related to computers, software and new technology.