How to set up Wi-Fi for byfly. First, let's check whether the main cables are connected, this doesn't take long, but sometimes it saves a lot of time

Using step by step instructions described below, you can easily configure the ByFly router via the Promsvyaz M-200 A modem.

Connecting a modem to a PC

Before you start setting up the M-200A modem, you must:

1. turn on the computer;
2. check the network equipment on it;
3. if necessary, update drivers on network adapters;
4. Now you need to connect the power cable to the Promsvyaz router and connect it to the power supply;
5. Insert the cable into any port of the modem twisted pair, which is larger than a telephone connector and has a thick connector, and connect its other end to the computer into the network port;
6. Insert the phone cable into the corresponding connector of the router (LINE) and into the MODEM connector. And its LINE connector is in telephone socket. Connect the phone itself to the PHONE connector of the splitter.

Press the power button on the router; it is located on the right side of the back of the case, near the antenna. Make sure all the lights are lit or flashing green as shown in the photo.

If the computer does not see the modem, then most likely it is on it old system or viruses. Reinstall Windows or update your antivirus.

The M-200A modem is configured by default in bridge mode, that is, it connects the computer and the Internet provider. But every time you access the Internet, you need to connect through a special shortcut. This brings some inconvenience, so it is better to configure a modem in the router. Then the computer and other devices will receive the Internet immediately from the M-200A.

Login to the interface

To start setting up your router ByFly Promsvyaz, you first need to go to its interface:

Setting up a router on ByFly

At the top of the page you will see the modem menu, and below it there are settings divided into blocks. To configure ByFly in router mode, in the page that opens, select the Interface Setup tab and then the Internet subtab.

Photo: Internet subtab - entering settings

Set all parameters:

• in Virtual Circut select PVC0;
• Status should be Activated;
• in VPI we write 0;
• VCI – 33;
• ATM QoS – UBR;
• click on the button next to PPPoE/PPPoA, then additional settings will open;
• in Username, enter your contract number and @beltel.by, without a break. Below is the password specified in the contract;
• Bridge Interface – Activated;
• Connection – Always On – never disconnect;
• Get IP Address – Default;
• Nat – Enabled;
• Default Route – Yes;
• Dynamic Route – RIP2-B or RIP2-M;
• Multicast – IGMP v2;
• Direction – Both;
• click SAVE.

Video: Setting up the ByFly router mode on the M 200A modem

Device in “router” mode

The router is designed to control other devices on the network. It distributes IP addresses, so several devices can access the Internet from one connection. Click on the Lan tab in the Interface Setup section to check the DHCP settings. In general, it is configured automatically in 90% of cases, so it is better to double-check. It is DHCP that assigns IP addresses on the network, and DNS that converts domain names into ones that the browser can understand. Therefore, to configure the M-200A modem in router mode, compare the data on the tab and what is in the figure.

Photo: Lan tab in the Interface Setup section

Main IP Address should be 192.168.1.1, Sabnet Mask – 255.255.255.0. Enable DHCP (click Enabled).

Check DNS Server with your ByFly server at your place of residence:

• Minsk: 82.209.240.241;
• alternative DNS server: 82.209.243.241;
• Minsk region: 82.209.253.2;
• Brest and Brest region: 82.209.195.12;
• alternative DNS server: 193.232.248.2;
• Vitebsk and Vitebsk region: 82.209.200.16;
• alternative DNS server: 82.209.200.17;
• Gomel and Gomel region: 82.209.213.51;
• alternative DNS server: 193.232.248.2;
• Grodno and Grodno region: 194.158.202.57;
• alternative DNS server: 193.232.248.2;
• Mogilev and Mogilev region: 194.158.206.206;
• alternative DNS server: 194.158.206.205;

Click SAVE. Automatic distribution of IP addresses is enabled. Reboot the modem for the settings to take effect.

The Internet now connects automatically when you turn on your computer. At correct setting On the modem another light comes on next to the Internet sign. The connection is ready. You can check this by going to any browser, or pressing the key combination Win+r and typing ping f6.by –t in the line, and then pressing ENTER.

The following messages should appear:

Wireless Wi-Fi network

For Wifi distribution network via a Promsvyaz router you need:

1. click on the Wireless tab in Interface Setup;
2. in Acces Paint and PerSSID Switch select Activated;
3. in Wireless Mode set to 802.11 b+g+n;
4. if you want to limit the number of connections to the network, specify the required number in Station Number (from 0 to 16);
5. you need to put a password on the network so that someone else cannot connect to it without your knowledge;
6. to do this, select Broadcast Ssid –Yes;
7. in Ssid write the original name Wifi networks, which you will distribute through the router, and in Pre-Shared Key - strong password at least eight characters. It is better to use the WPA-PSK/WPA2-PSK encryption type in the Authentication type item;
8. in Encryption, select TKIP/AES.
9. By activating the Wireless MAC Address Filter and adding allowed addresses to the list, you can turn off encryption within the network. Wifi will then be available only to those devices whose addresses have been registered.
10. click SAVE. You can compare your filling with the example in the picture.

Photo: Configuring Wireless parameters in Interface Setup

To check if Wifi is working, you need to turn it off. network cable from the computer, connect to the created wireless network and enter the password you created earlier by clicking the checkbox - they will connect automatically. The Internet should work. If suddenly the pages do not load, check the drivers network card or router settings.

The local network

The Promsvyaz M-200A modem is also used as a switch if you connect several computers to it via a cable. You can set up file sharing between them by creating a local network. You can also configure ports for uTorrents to download different movies, audio and documents over the network.

In the Advanced Setup tab you need:

Setting up ByFly Internet

If you have completed all the above points, then ByFly Internet via the Promsvyaz modem is configured.

You can access the network simultaneously from several computers and distribute Wifi. If you connect the phone cable directly to network adapter computer or M-200A modem, but not configured, Internet access will also be available. But to do this you need to connect ByFly for your Windows.

For the Windows 7 operating system, the Internet is configured as follows:

• open the Start menu;
• in it, click on Control Panel;
• then select Network and Internet;
• behind it is the Network Control Center and shared access;
• select setting up a new connection;
• and in it – Internet connection;
• check High Speed;
• Enter the username and password specified in the agreement with Beltelecom. Username – contract number + @beltel.by;
• check the box - Remember this password;
• You can write any connection name;
• and select – Connect.

Go back to the Network and Sharing Center and in the left corner of the window, click Change adapter settings.

On the created connection, right-click and in the window that opens, click Create shortcut. An icon will appear on the desktop through which you can connect to the Internet when needed. Now you know all the ways to connect the ByFly Internet and configure the Promsvyaz M-200A modem. If it is not possible to carry out cable system for connection and output to in your premises (house, cottage, office, country house or apartment) or it is not economically profitable for you, you should seek help from specialists who will help you connect and configure an ADSL modem with a built-in Wi-Fi transmitter.

Wireless Fidelity is considered the global equipment standard. It is designed to organize connections wireless networks, whose radio communication has a broadband range.

Wi-Fi modems make it possible to freely access the Internet in any place convenient for you where there is an access point. Modems fully comply with certified devices with designated Wi-Fi logos, transmitters emit the lowest level of radiation in operating mode (lower level than mobile), by using Wi-Fi connections the user receives 100% mobility and is always in touch, both for personal needs and for work.

Now we’ll take a closer look at how you can set up Wi-Fi on ByFly yourself. Let's take a modem as an example. .

Connecting to the M-200A modem

To start setting up, you need to go to the web interface of this modem. After loading the browser, you must enter 192.168.1.1 in the address bar and press the enter key.

If you did everything correctly, the page will load and you will be asked to fill out the admin username and password fields. Use default login and password values ​​and enter the word admin.

Solving problems when setting up Wifi

If you do not receive a request for a name and password, you should check that the modem is connected to the computer correctly. Then try to get its IP address from the modem again.

To do this, you need to go to the properties of the wired network connection, then to the properties of the TCP/IP protocol (this is Internet Protocol version 4 for Windows 7), there should be a checkbox to automatically obtain an IP address.

To search for network connections, you need to do the following with your operating system:

Windows XP: go to the control panel, there to network connections.

Windows 7: go to the Network and Sharing Center, then open the adapter settings changes.

If, after the work done, you cannot access the web interface of this modem at the specified address in the address bar, then you need to reset all modem settings to factory settings. Take the modem, turn it over and look for a small hole at the bottom. It must be signed as reset or reset. Find a needle and press it on the button located in this hole. Hold it for 5-10 seconds and then release. This way the modem will reboot itself and the settings will be reset to factory settings. Such a reboot can be resorted to if the modem was already configured correctly and any changes to its parameters were accidentally made, which led to incorrect operation.

Setting up ByFly Internet

And now you are taken to the web interface of the modem being installed. On the screen, in the upper part, there is a modem menu, at the bottom of the screen its settings, which are divided into blocks. To configure the modem correctly wifi byfly you need to go through 2 stages: at the first stage, the modem is configured as a router, and at the second stage, an access point is configured (which is WI FI).

Let's start the first stage– setting up the modem as a router. We work with the top menu and click, in turn, Interface Setup and just below – Internet. ISP parameter, in the Encapsulation block, check PPPoA/PPPoE, after which the settings window will be the same as in the illustration. In this PPPoA/PPPoE settings block, fill in the Username field and enter the user name there, and enter the password in the Password field. Bridge Interface parameter – check the Activated box, and check Yes in the Default Route parameter. After making changes to the modem settings, you need to save them by clicking the Save button (at the bottom of the screen). The stage of setting up the modem as a router is over. Now you need to set up a Wi-Fi access point.

Wi-Fi setup

In the top menu you need to select Interface Setup – Wireless. The window will become the same as in the illustration below. The PerSSID Switch parameter must be set to Activated. With this parameter we activate Wi-Fi and all that remains is to configure the network parameters. The SSID parameter is responsible for the network name. It will be seen by all devices with a Wi-Fi module within the range of our modem. Authentication Type and Encryption parameters are responsible for the security of the Wi-Fi network as a whole. The marks should be set as shown in the illustration. In the Pre-Shared Key field, you must enter the password you created for your Wi-Fi connection. It is most secure when the password consists not only of numbers, but also contains letters. The password must not be less than 8 characters. By clicking on the Save button you save all the settings for Wi-Fi connection and data transfer.

After filling out and saving all the necessary blocks with settings, you can safely disconnect the cable from the computer and connect to the newly created Wi-Fi wireless Internet network, where you will need to enter a password.

If everything is configured correctly, then access to the Internet can be achieved anywhere within the modem’s range.

We also watch the video: how to set up Wi-Fi on ByFly

.

Setting up ByFly Internet. Connection to wifi beltelecom. All the necessary settings for the modem from Beltelecom are described here: for the modem to operate in ByFly router mode - the Internet works automatically immediately (without connecting through a shortcut), it becomes possible to connect several computers (laptops, phones, tablets) at once - thus creating a home wireless network, to set up a Wi-Fi connection where the modem itself acts as the access point.
To set up, we need a working computer, laptop, netbook, without viruses, a modem (aka router and Wi-Fi access point), Promsvyaz and a network cable (included), connected to the By Fly Internet service.

Descriptions of connecting modems and wireless access points D-Link, Zyxel are not covered in this article.

To correctly configure ByFly Internet and wi-fi connection necessary:
- connect the cable to the network port of the computer (laptop) 2 or 3 port of the modem.
- turn on the power in the computer, laptop and modem. Wait until the system on the computer is fully loaded and the modem-router is initialized.
- it is advisable to remove the old antivirus (especially if it is not updated - it may block). Sometimes you have to reinstall Windows, since the main problem is often not the modem, but a virus-ridden computer, and the Internet does not work, it works slowly and with interruptions precisely because of this.
- launch OPERA browser,IE.
- V address bar enter (without spaces) the numbers: 192.168.1.1 (this is the address of our ByFly modem online).
- press ENTER.

Enter in both windows (password and user): admin (5 letters in English).
We get into the modem interface.

Click the Interface Setup tab. We go to the Interface Setup tab and the Internet subtab.
Everything should be like in the picture below.

You need to change the fields: username (in the Beltelecom agreement - the user), password (in the agreement this is the password) and Bridge Interface. We check if the Default Route checkbox is active and set to YES.
Click SAVE.
Click the LAN tab. You can't change anything here ( DNS servers will rise automatically!)
Or as in the picture for the city of Minsk. We transfer the DNS Relay to the USED USER DESCOVERED DNS state (use user-defined DNS servers - indicate for your region, in the figure DNS By Fly for Minsk.)

If changed, click SAVE.
If you use the modem as a wired router (i.e. you don’t need w-fi), further setting up By Fly internet not required, not only that, it is also undesirable. Activating the wi-fi module in the modem will make the device a source of radio interference, electromagnetic radiation (not good for health), and a “back door” for an attacker.
Click the Wireless tab. This is the wireless wi-fi connection setup for By Fly.

We change only what is indicated by the arrows in the picture.
We activate the wi-fi module in the router (it can be disabled by default - the menu items are not active).
As a rule, you need to put the point in the Activated position in the Access Point Settings menu.
Be sure to change the Pre-Shared Key item. This is your password to log into your wi-fi network. For convenience, change the SSID - this is the name of your network, make it unique so that you can recognize it. Call it (for example) BIGMAN (English layout is required), or in your own way.
Click SAVE.
The modem is ready for operation. Disconnect the network cable from the computer (laptop) to check wi-fi works(if it's necessary).
We turn on the wi-fi card on the laptop - look for the network (as specified in the SSID). Click connect, enter the password that you entered during setup in the Pre-Shared Key item.
Everything should work. If your computer or laptop does not display the network, the driver for the network card may not be installed, or there may be other problems.
Thus, a sufficient number of devices can be connected to our wireless network, as well as via cable, at the same time, which will work with the Internet connection without interfering with each other.

Byfly is trademark Beltelecom company, which provides access to high-speed Internet. It so happens that users are not always able to correctly configure network access themselves. This applies to both home Wi-Fi connections and public ones. In this article we will consider both options.

Methods for connecting to public Wi-Fi

byfly wireless access points are installed in many public places, accessed through a user login and password. This data can be obtained temporarily, or you can secure it for a long time. Both methods are presented below.

Temporary free access

It is convenient to use this option if you urgently need to go online, but do not want to make a map and enter into an agreement. Setup takes a couple of minutes.

1. Turn on Wi-fi on your device and connect to the network.
2. Go to your browser and try to access any website.
   
3. After the authorization page appears, enter your phone number and select the access time of “15 minutes.”
   
4. You will receive an SMS with your login and password.
   
5. Enter these details on the login page and click “Login”.
   
6. Ready! You can use the Internet for 15 minutes.

Note! If you need more than 15 minutes, then indicate the required quantity and pay the selected tariff.

Permanent access

This tariff without subscription fee gives the right to top up the card and use Internet access at any time. You can get the card at service center Beltelecom, having concluded an agreement. This option is the most convenient for city residents.

Important! To receive a card, you must have identification documents.

Setting up a home modem

We've sorted out setting up a public network, now let's start setting it up Wi-Fi at home. All actions must be performed on a PC with a modem connected to it via a cable. The setup is carried out using the example of the Promsvyaz M-200A device.

1. Go to your browser and enter "http://192.168.1.1"
2. In the window that appears, enter your login information. The default login and password is “admin” (If the login window does not appear, see the following instructions).
   
3. Click "Interface Setup" → "Internet".
4. Set the “ISP” parameter to “PPPoA/PPPoE”.
5. In the “Username” and “Password” fields, enter the user’s login and password (This data can be found in the contract for the provision of Internet connection services).
6. Set the “Bridge Interface” parameter to “Activated”, and below the “Default Route” parameter - “Yes”.
   
7. Click "Save".
8. In the top menu “Interface Setup” → “Wireless”.
9. Set the “PerSSID Switch” parameter to “Activated”.
10. Create a name and password for the Wi-Fi network.
    
11. Click "Save".

After completing these steps, you will have a Wi-Fi access point ready to use.

If you do not see the login window, configure the network card.

1. By right-clicking on the network icon, go to the “Network and Sharing Center”.
2. Go to “Change adapter settings”.
   
3. Right-click on the “Connect via local network» → “Properties”.
   
4. Select Internet Protocol Version 4 TCP/IPv4 → Properties.
   
5. Check the box next to “Use the following IP address.”
6. In the IP address line enter “192.168.1.2”, enter the subnet mask “255.255.255.0”, and in the “Default gateway” enter “192.168.1.1”.
7. Enter the addresses of DNS servers (you can find them on the website

Having replaced the modem or connected to the services of a new operator, we are faced with the need Wi-Fi settings- connections. You can call the service technical support, or you can try to set up Wi-Fi on ByFly yourself, which is what we suggest doing using our instructions.

Calling Beltelecom technical support (especially in the evening on weekdays) can be a very time-consuming undertaking. In those 10-15 minutes that you are “hanging on the wire”, the long-awaited Wi-Fi can already be configured using our instructions.

1 Setting up a network card

After you have connected the modem to the network and the PC to the modem using a network cable, you can proceed to setting up the network card.

1.1.1 To configure a network card in Windows 7, you need to click the “Start” button, go to the “Control Panel”, and in the window that opens, select “Network and Internet” - “Network and Sharing Center”.

1.1.2 In the new window you need to select “Change adapter settings”. Right-click on the “Local Area Connection” shortcut. In the dialog that opens, select “Properties”.

1.1.4 In the IP address line you must enter the values ​​192.168.1.2, if you use several computers to connect, then the numbers that you put in the last column in the IP address line should not match.

1.1.5 In the next line, “Subnet mask” should be determined by itself. Its value is 255.255.255.0. The next line is “Default gateway”, enter 192.168.1.1.

1.1.6 All that remains is to enter the DNS server addresses (depending on your place of residence). You can find them on the website byfly.by in the “Customers” section. For Minsk and the Minsk region, enter 82.209.240.241 in the “Preferred DNS server” line, and 82.209.243.241 in the alternative DNS server line.

After all the fields are filled in, click “Ok”. In the previous window (“Local Area Connection - Properties”), click “Close”, and also close the window with network connections.

1.2 Windows 8 and Windows 10

1.2.1 On the computer icon (at the bottom of the screen), right-click and select “Network and Sharing Center”. Next (in the left part of the window) select “Change adapter settings”, right-click on the “Ethernet” shortcut and click “Properties”.

1.2.2 As in the case of setting up a network card in Windows 7, select the line Internet Protocol version 4 (TCP/IPv4) and click the “Properties” button. Next, fill in the fields in the window that opens. Data for this is in paragraphs 1.1.4-1.1.6 of our instructions.

1.2.3 After all the settings have been entered, click the “Ok” button and close the unnecessary windows.

1.3.1 For Windows users XP settings are slightly different: “Start” - “Control Panel” - “Network Connections”. Next, right-click on the “Local Area Connections” shortcut and select “Properties”. In the “Components used by this connection” window, select “TCP/IP Internet Protocol” and click the “Properties” button.

1.3.3 After all parameters have been entered, click “Ok” and close the previous windows.

2. Setting up the modem

The next step in setting up wireless connection there will be a modem setup. Here your actions may differ depending on the modem model you received from your operator.

However, for any modem, the setup begins with a browser window in which you need to enter the address 192.168.1.1. Next, in the window that appears, enter the user name and password (admin, admin) and click the “Ok” button. And we find ourselves in a window with the modem interface.

When setting up most modems, the common thing is that the user needs to make settings in the connections menu (Wireless). The standard steps when setting up a modem will be to enter the network name (make up your own) in the SSID line and the password to log into it (the line may have the name Pre-Shared Key, passphrase).

For some models of Huawei modems, you must first click on the “Basic” button on the right side of the modem interface, and in some models you must go to the WLAN tab. Often Huawei modems you need to additionally switch to the “Activated” mode. You need to come up with and enter a password that you will use to connect to Wi-Fi in your home or office. The new modem settings must be saved (Save or Submit buttons).

In ZTE modems, to proceed to setting up the connection, you may need to go to the Network – WLAN – Multi SSID Settings tab. Next, in ZTE modems you need to check the “Enable SSID” line, and in the Name SSID line you need to enter an arbitrary name for your network. After saving the settings (Submit button), you need to go to the security settings (Security button on the right side of the interface of ZTE modems from ByFly). In the WPA Passphrase line we delete standard password and register our own, which we will use to connect to Wi-Fi. Save the settings (Submit button) and exit the modem interface (Logout button in the upper right browser window).

If you want to use Wi-Fi not only on mobile devices and laptops, but also on desktop computer using a Wi-Fi adapter, then to set up Wi-Fi you will need to perform one more step.

3 Setting up a wireless network connection on a PC

3.1 Setting up a wireless network connection on a PC for Windows 7

3.1.1 Go to the “Start” menu - “Control Panel” - “Network and Internet” - “Network and Sharing Center”.

In the window that opens, select “Change adapter settings”, then right-click on “Wireless network connection”, in the new dialog select “Properties”. In the next window, select “Internet Protocol Version 4 (TCP/IPv4)” and click the “Properties” button.

3.1.2 We assign IP and DNS addresses that need to be used.

IP address for the ADSL network: 192.168.1.3, for the GPON network: 192.168.100.3, the gateway mask should be determined by itself (255.255.255.0), the main gateway is 192.168.1.1 and 192.168.100.1.

Preferred DNS server: 82.209.240.241, in the line the alternative DNS server is 82.209.243.241. Click "Ok" and close the "Wireless network connection - properties" window.

3.1.4 The “Current Connections” window that appears should display all available Wi-Fi networks. Among them, you need to select your network, the name for which you came up with when setting up the modem (SSID line).

Select your network and click on the “Connect” button. In the window that opens, you must enter the security key, that is, the password that we also set when setting up the modem. Click "Ok". After the connection of the PC to the network is completed, you need to disconnect the network cable to check the operation of the Wi-Fi connection.

3.2 Setting up a wireless network connection on a PC for Windows 10

3.2.1 We repeat the steps from paragraph 1.2.1.

3.2.2 In “Related parameters”, select “Adapter settings”. On the “Wireless Network” shortcut, click on “Properties” - “IP version 4 (TCP/IPv4)”, select it, click “Properties” and get into the next window, fill in all the necessary lines with the values ​​​​from paragraphs 3.1.2. Click "Ok". Close the “Wireless Network Connection” window.

3.2.3 Right-click on the “Wireless Connection” shortcut. Click “Connect/disconnect” and select from the list of available Wi-Fi networks my. When you click on its name, a “Connect” button will appear. In the password line, enter the password that was set when setting up the modem. Click “Next” and wait until the PC connects to the wireless connection.

3.3 Setting up a wireless network connection on a PC for Windows XP

3.3.1 “Start” - “Control Panel” - “Network Connections”. On the “Wireless Network Connection” shortcut, right-click and select properties. In the new window, select “Internet Protocol TCP/IP”. Click on the “Properties” button.

3.3.2 In the new window, fill in all empty lines. We take the values ​​from clause 3.1.2.

3.3.3 Next, in the “Network Connections” dialog, right-click on the “Wireless” shortcut network connection" In the dialog that appears, select “View available wireless networks.” In the window that appears, select the network with the name that you specified in the modem settings (SSID line). Next, you need to click the “Connect” button. In the “Network Key” line, you must enter the password that was set when setting up the modem. In the second line you will need to confirm it.

After the connection is completed (the corresponding dialog box disappears), you need to disconnect the network cable from the PC.

Important for any OS. If the modem is in Bridge mode, then to connect to the network you need to additionally launch a PPPoE connection specifying your login and password.